Why would you need to make an entry door repair? What do people see when they walk up to your home? It is usually your front door. Do you really want them to see a sign saying Front Door Broken – Use Side Door? Most of the time there is no need for that. Entrance door repairs can be made without too much difficulty.

This article will discuss some common problems that occur with front doors. There are both visual and operational concerns with an entrance door. Visually, you may need to paint or caulk some items that need attention. You want your door to open and close correctly, the locks to provide security and the weatherstripping to keep the heat or cold out. These features can be addressed without replacing the door. Read on and evaluate what you need to do, to make your own entry door repair.

Entry Door Repair - Information

That depends on who you talk to. Many websites and companies will equate an entry door repair with front door replacement. A decent off the shelf pre-hung entrance door will run from $250 to $600. High end doors can run into the thousands of dollars. It will cost another $150 to $250 to have it installed, assuming there are no problems.

You may be fortunate and find a carpenter that will repair the door and be honest with you. Minimum it will involve a service call, around $50 plus any parts. This would be to adjust the door or weatherstripping. You will need to be the judge on whether or not you want to be sold a new door. So you could save from $50 to $850. The lower figure is for something that might take you fifteen minutes to accomplish.

The range of tasks we are talking about start with simple adjustments on up to removing and replacing a section of the door jamb. Replacing your door is a subject for another website.

Over time doors get out of adjustment, this will cause them to sag and not close correctly. The common culprit is the top hinge. Check the adjustment on the door before you do anything. Weatherstripping, either replacing or adjusting is another simple fix. The alignment on the strike plate can also cause the lock not to work.

Worst case, you take the door out and cannot get it put back in. Your entry door repair problem has escalated. This will leave you with a big hole in the front of your house. You can put plywood over it temporarily. You can also make things worse if you start adjusting things the wrong way. A sticking door could turn into a door that won't close at all. Make sure you understand what you are trying to accomplish before you do anything.

Troubleshooting Entry Door Problems

The steps below give you instructions for adjusting a door. This would also include dealing with a sticking door. Wood doors can swell and stick. Does the door stick every year during the rainy season? If it does, planing or sanding it may solve the problem. Most of the time, a sticking door needs to be adjusted. This is especially true if it is the upper strike side that is sticking.

Locks and Deadbolts Not Working

Is it the door lock or deadbolt that is not working? Locks and deadbolts have their own set of problems. See the article on 'Door Lock Repair', for information on adjusting, repairing and replacing door locks.

Another common reason that locks don't work right is a door that is not adjusted properly. When the locks don't align with the strike plates, the won't lock or won't stay locked. See the article 'Adjusting Exterior Doors' and 'Adjusting Door Locks to Strikes' for more information.

Door Is Leaking Air

Is the door leaking air or can you see daylight around it? You need to repair or replace the weatherstripping. See the article on 'Weatherstripping for Doors', for more information. Doors can leak both cold and heat out of them. You can save yourself some money by keeping it in good repair.

Damaged Door Jambs

Is your door jamb or door frame in need of repair? Is it cracked or split? It is also possible to have rotten wood near the base. The steps and info you need are found in the article 'Door Frame Repair'. Find out what you can do to repair the door frame without replacing the door.

Door Will Not Close Properly

Entry door problems will normally be associated with three key areas. The alignment of the door, the hinges and the hardware that is attached to the door. Read below to determine where your problem lies and the select the appropriate link.

Is the door hard to close or open. Try to determine where the friction is occurring. There are two spots that take the prize most of the time: (1) The upper corner on the latch side of the door (the side with the door knob). (2) The bottom of the door, again on the latch side. Both of these conditions indicate that the door is sagging. Over time the weight of the door pulls on the top hinge and loosens it up. See the article 'Adjusting Exterior Doors' for instructions on tightening the top hinge and checking the door for alignment. This is a very common entry door repair problem.

Swollen Wooden Doors

Humidity can make a wooden door swell in the summer, causing it not to close. If this is a persistent problem, you can sand or plane the door to take enough material off the door so that it will close. Caution should be used when doing this. Later, in the winter, the door will shrink and may result in a gap if too much wood is removed.

Are you sure the door is swelling? This is only going to be true if it is an all wood door and it is not sealed very well. Check the margins first before you start sanding or planing a door. See the article 'Sanding and Planing a Door' for instructions on sanding or planing a wood door.

Tight - Rusty - Squeaking Door Hinges

Another entry door problem is when the door is hard to move even when it is not going into the frame? Are the hinges squeaking or making noise? The hinges may be binding up. See the articles, 'Lubricating Door Hinges' and 'Replacing Door Hinges' for instructions and information on what to do with door hinges.

Summary

Hopefully, you have been able to get your entrance door working properly. Learning how to adjust a door is a handy thing to know. Doors will often act up. Many of the same principles apply with all doors. Getting the weatherstripping right is important when it gets cold.

For swinging doors, remember that the top hinge is doing all the heavy lifting. With a little patience you have been able to make your own entry door repair. Congratulations, not everyone can do this!

Knowing 'How To Fix a Door' can save you both 'time' and 'money'. Many times all a door needs is a little TLC to get it functioning properly again. Review the 'Troubleshooting Guide' below to figure out what your problem is and how hard it will be to fix.

The door that is giving you trouble will likely be in one of these categories: (1) 'Entrance or exterior doors', (2) 'Garage doors', (3) 'Interior swinging' and 'Pocket doors' and (4) 'Closet doors'. Each of these pages has links to all the related topics for that door type.

Use the section on 'Troubleshooting Broken Doors' below to identify common door failures. Unsure of what type of door you are trying to fix? See the next section on 'Types of Doors in Your Home'.

Types of Doors in Your Home

You have several types of doors in your home. An average home can easily have between ten and twenty doors in it. Larger homes can have many more. Understanding the differrent types of doors will help you to isolate and fix your problem quickly.

• Exterior Doors - Any door that separates the inside of your home from the outside would be considered an exterior door. These are the doors that protect you from the elements.
• • Entry Door - Most homes have at least two entry doors, a front door and a back door. Typically these are swinging doors that may or may not have glass panels in them. Thay can be made of wood or composite materials. These doors need to be made of insulating materials and usually require separate weatherstripping. Of all the doors in your home, your entry doors do the most work and have the highest expectations. 
  • Patio Door - A patio door as the name implies usually opens onto to patio, porch or deck. They can be a french style door or some other type of swinging door with a large glass lite in them. Double patio doors can have one or both panels that operate. Patio doors can have alignment and weatherstripping issues. Double swinging doors often have issues with the lock sets.
  • Sliding Doors - More like a window than a door, sliding glass doors are used for access to outside spaces. Like a patio door they often open onto a deck or porch. A sliding glass door usually has one fixed panel and one moving panel, although other configurations are possible, including doors with three panels. The panel that opens has rollers that follow a track on the top and bottom of the door. Problems with the door staying on the track, noisy and sticking rollers and latches that don't lock are some of the problems that you can encounter.
• Garage Doors - This is the biggest door in your house. It is also one of the most complicated. Since garage doors are heavy they use springs to help lift the weight. Add to that the use of garage door openers and you have a potential for quite a few problems.
• Interior Doors - No mystery here, if it is not keeping the cold and heat out, it is an interior door. Doors on the inside of the house are used for both privacy and concealment. Bath rooms and bedrooms obviously need privacy. Closet doors conceal things that we don't want to look at all the time.
  • Swinging Doors - Bedroom, bathroom, sometimes closets, basements, dens and media rooms are all candidates for this type of door. A swinging door is your most common type of door and is used for any room that needs to have some level of privacy or concealment some or all of the time.
  • Pocket Door - Pocket doors are used in lieu of swinging doors in situations where space is limited. A pocket door slides into the wall and can provide additional floor area, especially in tight places like bathrooms. They have special problems and needs.
  • Sliding Doors - Interior sliding doors are used on closets. There are two or more leaves that slide along a track, providing access to the things inside of the closet.
  • Bifold Doors - Bifold doors have been the popular choice for closet doors in the last few decades. They are inexpensive and easy to install. They have the advantage of being able to open up the entire width of a closet at the same time.

How To Fix a Door - Troubleshooting

Swinging Doors - Interior & Exterior

Door Won't Close

A door that won't close or refused to open can be very irritating. Putting your foot on the wall when you try to open the door or using your shoulder to close it are two obvious signs.

Couple of things to consider. Is it a wood door? See the next section on doors that rub or stick., it could be swollen from high humidity.

Another test to locate the problem would be lifting up on the door handle when you try to open or close it. Does it work easier when you do that? If so, the top hinge is loose or out of adjustment. This is an adjustment issue and can be fixed. See one of these articles, depending on which type of door are dealing with,  'Adjusting Interior Doors' and 'Adjusting Entry Doors'.

Door Rubs or Sticks in Frame

In years gone by this was a common problem with wood doors. Especially in areas that have high humidity during some seasons. The wood in the door and frame will swell and then the door won't close. When this is your problem it is most likely that the door sticks along the full length of the jamb. For instructions on this topic, see 'Sanding and Planing a Wood Door'.

When the door sticks, where does it stick at? A common location for any type of door is the upper corner of the strike side (the side with the door knob) of the door. When this happens it is most likely that the door is out of adjustment. This can be a simple fix if you follow the instructions found in the articles 'Adjusting Interior Doors' and 'Adjusting Entry Doors'.

Door Hinges Stick and Squeak

Do you have stiff squeaking door hinges? This problem can be annoying, and may ruin the hinges over time. The good news is that rusty squeaky hinges can be restored to good working order. On rare occasions you may need or want to replace them.

For a complete discussion on dealing with hinge issues, see the series of articles on 'Squeaky Door Hinges'. If you are sure you need to replace them, see the article 'Replacing Rusty Door Hinges'.

Door Does Not Latch Properly

Do you have trouble getting the door lock to latch properly when you close it? Do you need to lean on the door to get it to catch? Or does it pop open when you think it is closed? Worse yet, does the lock refuses to set, no matter what you do?

These are common problems with door locks. Most of the time the door lock gets all the blame for issues like this. Most of the time is is not the door lock's fault. Instead the fault often lies with the door or the way it is positioned in the frame. The problem may also be caused by the strike plate, a strike plate that is not positioned correctly may keep the lock from latching correctly.

The first and easiest thing to check is the adjustment of the door. For exterior doors see the article 'Adjusting Entry Doors'. Interior door adjustment is covered in the article 'Adjusting Interior Doors'.

Cold Air Coming In Around the Door

This is a common problem, especially in colder climates. When you put your hand by the edge of the door you can feel cold air. The colder it gets the colder the air feels. You may be able to feel the air around the entire perimeter of the door, or it may only be in certain spots. Another variation is cold air coming in at the bottom of the door.

There are two problems that can cause a door to have gaps. The first is the adjustment of the door. Even with the proper weatherstripping and poorly hung door will not seal properly. Adjusting the door can solve this problem. For information and instructions, see the article 'Adjusting Entry Doors'.

The other issue could be the weatherstripping, it may need to be replaced, see the article 'Exterior Door Weather Stripping' for more information.

Garage Doors

Garage Door Will Not Go Up

Garage doors are very heavy and they use the internal tension of coiled springs to help offset the weight. When the springs break it is very difficult to lift the door. A broken spring is the likely cause of a door that you can't raise. See the article 'Garage Door Spring Repair' to help identify your problem.

Another potential cause would be a garage door that binds and sticks. This is usually an adjustment issue. For information on this subject, you can review the articles 'Adjusting a Garage Door' and 'Adjusting a Binding Garage Door'.

Garage Door Makes a Lot of Noise When it Operates

Garage doors are louder than most doors. They have several moving parts including hinges and rollers. Added to that, the tracks that support the door will flex when the door opens, creating further noise. Certain types of doors, such as all metal doors with no insulation, are especially loud.

With those comments aside, squeaky and sticking rollers and squeaky hinges can add to the noise level. See the articles on 'Lubricating Garage Door Rollers' and 'Oiling Garage Door Hinges' for some advice on how to cut down on the noise.

There is Daylight and Cold Air Coming In Around My Garage Door

If you have an attached garage, you probably don't want a lot of hot or cold air coming in around the door. Even if you garage is not conditioned space, you get some passive heating and cooling from your home. Why waste that? There are two key reasons why you have gaps around your garage door, (1) a door that is out of adjustment, (2) worn or missing weatherstripping.

For information on fixing the weatherstripping on your garage door, see the article 'Garage Door Weatherstripping'. The article 'Adjusting a Garage Door' discusses what you need to know about getting your door properly aligned.

Door Topics

Door Frame Repair

Who's the Trouble Maker, the Door or the Frame? When a door won't close correctly it may be rubbing on or hitting the frame. Is it the frame that is the problem? Occasionally. Often it is the door itself that needs adjusting. Follow the above link to see what can be done with a door that won't close correctly. You may be pleasantly surprised by how easy it can be to adjust a door.

The top hinge on any door does most of the work. It is also the hinge that is most likely to loosen up. There are ways to help it out. One long screw into the framing behind the top hinge can work wonders.

Entry Door Repair

Doorbell Rings, Which Door Do Your Head For? Homeowners and builders alike spend the most money on the front door. It makes a statement about the home and is the first thing visitors see. In addition, it is needed to keep the elements out. Locks and weather stripping are two key components on a front door. Follow the link above to learn what you need to do with entrance doors. It will help you keep your front and other entrance doors in good working order.

Interior Swinging Doors

Interior Doors are the plentiful in your home. These are easier to repair when compared to entrance doors, but there are more of them. Many times all that is needed is some adjustment, it may not be that hard. Follow the link above for information. It will help you deal with this type of door.

Closet Doors

I recently toured a couple of homes designed by Frank Lloyd Wright. Great architecture but not always practical. One key feature, he refused to design closets into his homes. Something about clutter. My opinion there are a lot of things you would rather have in a closet.

In recent decades the bifold door has taken center stage for closets, although, sliding doors are still common. Learn how they work and what you can do to repair them by following the above link.

Pocket Doors

A less common, but very useful door is a pocket door. They are often used when space is tight. They disappear into the wall, is that great or what? They do have some unique problems. See the article on for the special problems with this type of door.

Garage Doors

What's the Biggest Door You Have? Of course I am talking about the garage door. It is the biggest, the heaviest and has the most moving parts. Things can break and get out of adjustment. You may have a garage door operator that can act up as well. For information on garage doors, follow the link above. This will help you deal with the problems you are having with your garage door.

It does not matter whether you use your garage for the car, an entrance or a storage facility. You still want the door to work properly. You can make garage door repairs without taking the door down. Check out the information before you call a serviceman.

Door Repairs the Safe Way

The main safety concern with door repair is the use of tools. Make sure you are familiar with safe practices for the tools you use. Another concern is the weight, make sure you are physically able to wrestle with a heavy door. There are special safety concerns for garage doors, take note of these in the garage door articles. Getting help is always a good idea. Check the Safety Links page for guidelines on safe practices.

Tools

You will need standard tools, screwdrivers and chisels are the most common items. Power tools like a battery drill and a sawzall may be needed. Check the tool requirements for the individual repairs for more information on the needed tools.

How To Fix a Door - Summary

Can you make your own door repair? In most situations, the answer is Yes! Make sure you are familiar with the steps involved. Troubleshoot the problem to make sure you are focusing on the right problem. Obtain the materials and tools required before you start. Follow the steps and take your time and you will be successful. Do something you want to with the money you save.

Recently, two of the doors in my house quit working on the same day. Odd. My four year old grandson found a screwdriver and managed to remove the bottom hinges off the bedroom and bathroom doors.

He put the bedroom door hinge back on, unfortunately it was backwards. For the bathroom door, he got the hinge on correctly, but could only get the screws back in part way. This was not too difficult to fix and I was impressed by his display of mechanical ability.

Replacing door locks is a last resort. You have gotten this far, one of two things has happened. The lock is a goner and needs to be replaced. The other is, you decided that it looks terrible and a new one would look a lot nicer. Either way, you have to replace it.

For related information see the articles 'Troubleshooting Door Locks' and 'Troubleshooting Door Problems'.

Three things matter with a door lock. The size of the main bore, the size of the strike bore and the back set from the edge of the door. The back set is less of a problem than it used to be. Most new locks have adjustable back sets The two normal ones are 2 3/8" and 2 3/4". Most new locks support both dimensions. Does that 3/8" really matter? Well, yes. A 2 3/4" back set lock will not work in a door bored for 2 3/8".

Purchasing Door Locks

You will want to take the old lock out before you purchase the new one. Although locks have gotten more standardized over the years, there are still variations. Write down a few key dimensions before you go shopping.

Door locks start out a around ten dollars and can go up to over a hundred dollars. Like anything else, quality and appearance are big factors. Obtain a lock that will fit your door. Follow the instructions for installing it. Most of them work similarly. The strike cylinder goes in first and then the two halves of the door knob screw together with the key side facing out. One caution, lever locks are handed and not all of them can be reversed. Make sure you check this out if you obtain a lock with a lever handle.

Removing the Old Door Lock

Most of the time the only you tool you need is a phillips screw driver. Many, (but not all) residential door locks are held in place by two long machine screws. These are located on either side of the door knob on the inside of the room. When you unscrew them, the two halves of the door knob assembly should come apart.

The screws are fairly long, so if you use a hand screwdriver, it will take a little bit of time. It is best to alternate between the two screws so that you can pull the handle out part way. Otherwise the angle for the screwdriver may give you trouble.

Retaining Buttons

Some door knobs have a retaining clip that hold the knob on. Again this clip will be on inside of the room. It may be a long flat button or it may be a button inside of a small hole. You will need a small nail if it inside of a hole. You push in on the button and the door knob will release, allowing the cover plate to come off.

Inside of the cover plate you will find two screws that hold the main assembly together. Remove the screws and the two halves of the door knob will come apart.

Once the lock is taken apart, you can remove the strike assembly. This is held in place by two screws on the edge of the door. The strike plate is also held in place by two screws. If you are replacing the door knob you will need to remove all of these items.

Installing a New Door Lock

Once you have removed the old door lock, installing the new one is pretty simple. Again, assuming you have a lock that fits your door, you should only need a screw driver.

Installing the Strike Assembly

Most locksets have an adjustable backset, so they will fit a door that is either 2 3/8" or 2 3/4" to the center of the main bore. You may need to set the strike assembly to the correct backset before you install it. Take a quick look at the instructions. Once the backset is adjusted, intall the assembly with the two screws provided. Install the strike plate in the same mortise that it was in originally. If you have to trim it, use a sharp chisel, removing only enough wood for the plate to seat flush with the door jamb.

Installing the Lock

Put the half of the lock with the female cylinders that recieve the screws in first. Align the other half of the lock up with the screws and push the halves together. Make sure you start the machine screws with your fingers, getting them started by a couple of threads before you use the screw driver or power drill. Once the screws are tightened the lock is installed.

Test the function of the lock, make sure it closes, latches and opens correctly. Try locking the door and opening it with the key.

Lubricating door locks is an easy effective way to get them working smoothly. The door strike can be lubricated with the lock or knob still in place.

See the articles 'How To Fix a Door' and 'Repairing Door Locks' for a listing of door repair topics.

Purchasing Door Lock Lubricant

You want to use a silicone based non-staining spray to lubricate your locks. Graphite is not a good choice, since it can get on other surfaces and stain them.

Lubricating the Door Lock

Use some silicone spray and work the knob back and forth until it moves freely. The same may be true of the lock tumblers. Spray some lubricant inside the key hole. Use the key to work the tumblers until the oil sets in and the lock works.

The other moving parts of the lock will require that you remove the cover plates to lubricate them. Most locks are held together by two machine screws. The heads usually face the inside of the door. Residential grade locks can normally be taken apart with just a screwdriver. The lock should come apart in two pieces. The strike mechanism can stay in place once the knob and cover plates are removed.

Lubricate all the moving parts and work them until they move freely. Re-assemble the lock and the door should work. An old badly corroded lock or a broken lock, will probably not respond to just oiling it. A lock that is too far gone will need to be replaced. Check Step Six below for information on replacing a lock.